The project shown here is a microphone preamplifier that provides high quality amplification, optimized for use in computers, media and mobile applications. The pre-amplifier provides a differential input stage, making the device particularly effective when layout constraints force the microphone amplifier to be physically remote from the ECM microphone. This project features adjustable gain using…
A breadboard is a device for testing temporary electronics projects. Components used to test a circuit can be reused for other projects. None of the components are damaged.
Almost all people start to learn electronics using breadboard because it is the simplest way of making circuit. The photograph shows a typical small breadboard which is suitable for beginners building simple circuits with one or two ICs (chips).
This is an Isolated gate driver-based N channel Mosfet Arduino Nano shield based on Si8261ACC, which can be used in various applications like DC Motor driver, solenoid driver, led driver, bulb driver and heater driver, with 3A fast switching diode provided across the output for an inductive load which protects the circuit from back EMF. Arduino Nano…
This is yet another post related to LM317. The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and…
This Bluetooth music receiver connects to the Line-In or Aux input on your home audio system. You can then stream audio from your Bluetooth enabled cell phone or mp3 player to your home audio system. It comes with an AudioB plus Bluetooth module. Note：TSA6012 can auto-detect the Aux in/Line in Audio input. Bluetooth Audio source has higher priority….
This is yet another TDA2030A based audio amplifier DIY kit. The kit is retired and not so popular these days. An excellent tutorial on this kit is published on this website.
This is a 2x8W audio amplifier board integrated with Bluetooth 4.0. It has a perfect class-D architecture (based on TPA3110D2) and every channel has 8W power output. This board can be powered by any DC 8V-16V power supply. It can be used to drive any 4Ω or 8Ω passive speakers.
Description: In this project, Arduino first encodes the remote signals and decodes them to control LED brightness. First of all, connect the Infrared sensor as shown in the picture below. Then, press keys 0 through 4; Arduino stores the values for keys 0 through 4 and when the sketch runs, key 0 turns off the…
I recommend you to read and understand the basic theory of crystal radio published on this article:Â http://www.buildcircuit.com/how-to-make-a-batteryless-crystal-set-radio/ Making a batteryless/powerless radio is a great fun, but there are also some difficulties.
This tutorial shows all the steps required to build a flashing LED rotating windmill electronic beginner soldering DIY electronic kit. The kit gives an LED swirling effect after assembly. The swirling pattern can be stopped using the two tactile switches(buttons). It is a very basic electronic beginner project for beginners. You would need basic soldering…
This is yet another FM receiver DIY kit for electronics beginners and hobbyists. It uses the chip CXA1619. The kit package comes with all the components required to build the kit. The schematic and description is shown below: This is the PCB of the kit. The silkscreen labels can guide you through soldering. This is…
This is yet another ultrasonic range finder project using Arduino. We have done several similar projects in the past. It allows us to control a buzzer based on the distance detected by an HC-SR04 sensor, making it sound with a frequency proportional to the distance from an obstacle.
TSA3111 is designed audio amplifier factories and DIY users. Bluetooth/LINE IN select switch and audio input port are designed as JST connectors. So, users can install this amplifier board in a box and connect an external switch and RCA/Mono plug to make their own audio amplifier.
TSA3117B is designed for mass production and DIY users. Bluetooth/LINE IN select switch and audio input port are designed as JST connectors. So, users can install this amplifier board in a box and connect an external switch and RCA/Mono plug to make their own audio amplifier.
BuildCircuit has written few articles about audio amplifier and music modules. One of the most popular examples is “Audio amplifier using LM386“. This article is about a bit advanced audio amplifier made using TDA7052A. Download datasheet of TDA7052A It is not wise to connect an 8 Ohm loudspeaker directly to Arduino microcontroller pins. When we…
A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions and they are double throw (changeover) switches. The relay’s switch connections are usually labeled COM(POLE), NC…
