2X L298 DUAL DC MOTOR DRIVER BOARD FOR ROBOTS
2XL298 H-Bridge Dual Motor driver project can control two DC motors connected to it. The circuit is designed around popular dual H-Bridge L298 from ST. Motor supply 7V To 46V DC, Load 2Amp Each Channel. FEATURES Motor supply V2: 7 to 46 VDC Logic Supply V1 : 5V DC Input Signal: Enable, Dir. , PWM…
AC MOTOR SPEED CONTROLLER FOR MODERN APPLIANCES USING LS7311
The project specifically designed for motor speed control application in appliances such as blenders, etc. Tact switches provided for selecting/indicating from 1 to 10 power levels ( Speed Levels). The project is ideal for universal and shaded-pole motor speed control for modern appliances design. Eliminates awkward mechanical switch assemblies and multi-taped motor winding. FEATURES 10…
2.5A 2 PHASE MICRO-STEPPING STEPPER MOTOR DRIVER
2 Phase stepping motor driver is a tiny board based on STK682-010 hybrid IC from ON semiconductor and it can deliver current up to 2.5Amp and has supply up to 32V DC. It has multiple micro-stepping: Full step, 1/2th Step, 1/4th Step, 1/8th Step, 1/16th Step, 1/32th Step, 1/64th Step, 1/128th Step. Â PR1 trimmer potentiometer…
50V – 10A BIDIRECTIONAL DC MOTOR DRIVER USING A3941
This tiny board designed to drive bidirectional DC brushed motor of large current. DC supply is up to 50V DC. A3941 gate driver IC and 4X N Channel Mosfet IRLR024 used as H-Bridge. The project can handle a load up to 10Amps. Screw terminals provided to connect load and load supply, 9 Pin header connector…
Popular Android Apps for 12CH Bluetooth Arduino module
3.5A UNIPOLAR STEPPER MOTOR DRIVER
Unipolar stepper motor driver can drive unipolar motor up to 3.5A and supply range 10 To 50V DC. The board has been designed using STK672-442AEN IC. The STK672-442AN is a hybrid IC for use as a unipolar, 2-phase stepper motor driver with PWM current control and Micro-stepping. FEATURES Supply Up to 50V DC Input Logic…
MC33035 BRUSHLESS MOTOR DRIVER BREAKOUT BOARD
The board shown here is a breakout board for MC33035 brushless motor controller. It requires an output buffer IPM module or Mosfets to complete the closed loop brushless motor driver. MC33035 IC is the heart of the project; the project provides 6 PWM pulses as well 6 Inverse pulses outputs. On board Jumpers helps to…
4A PWM CONTROLLED UNIPOLAR STEPPER MOTOR DRIVER USING STK672-740
The project published here is a high-performance Unipolar stepper motor driver that offers PWM controlled high current output. An Arduino board and the project published here can be combined to create a good Unipolar stepper motor driver with micro-stepping, supply 36v DC and load current up to 4A. This board requires a sequence of 4…
15A 100V ISOLATED HALF-BRIDGE DRIVER
15 A 100V Isolated Half bridge driver project intended to be used for DC-DC converters, inverters, LED driver and motor driver applications. This projects is really helpful in industrial applications where noise is a concern since project provides optical isolation between microcontroller and high current output. ADuM4224 isolated precision Half-Bridge driver is the heart of the project. IRFR120 dual Mosfet is…
3V TO 5V BOOST DC-DC CONVERTER USING MAX711
The circuit shown here is a compact and high-efficiency boost converter that has been designed for hand-held equipment. This boost converter converts 2 cells (3V) DC power into 5V DC with output load current up to 500mA. Typical efficiency when boosting battery inputs is 85%. The circuit is based on MAX711 which integrates a step-up DC-DC converter…
50V TO 5V @7A SYNCHRONOUS BUCK (STEP-DOWN) CONVERTER
This module is a non-isolated 7A DC-DC converter. The module can convert any DC voltage between 7V to 50V to a 5V DC with load current up to 7A. The project has been designed around LM5116 Wide Range Synchronous Buck Controller IC. The design includes 6uH toroid inductor and two N channel MOSFETS. The operating frequency is 250 KHz. The LM5116 is…
SINGLE 18650 LIPO BATTERY TO 5V BOOST CONVERTER
This small board is based on the CS5171 boost converter from ON Semiconductor. The board is configured to be used with a single 18650 LiPo battery. The circuit converts single-cell 3.7V LiPo battery voltage to 5V with a load current up to 400mA. Board has been designed to fit on the backside of a single-cell battery holder…
USB (5V) TO DUAL OUTPUT +/-15V OR +/-12V STEP-UP DC-DC CONVERTER
This USB to dual output step-up DC-DC converter has been designed to be used in industrial automation control equipment, sensors, isolated operational amplifiers and test & measurement equipment that require bipolar supply voltages. The module provides +/-15V or +/-12V DC load current up-to +/-100mA. An onboard PCB solder jumper is provided to set the output…
200W LAMP FLASHER
200W Lamp Flasher kit is used to flash lamps, bulbs and halogen lamp to give your product that attracting look. Input supply – 6 ~ 12 VDC Output – upto 200 W lamp / bulb load Optically isolated Mains supply Onboard preset to adjust the frequency (speed) of flashing (1 Hz to 5 Hz) Power…
555 STEPPER PULSE GENERATOR
The 555 Stepper Pulse Generator kit will help you with the pulse required to drive your favorite DC Servo Motor application. This kit uses the famous 555 timer IC for generating the Stepping Pulse. Input – 5 – 12 VDC @ 25 mA TTL/CMOS interfaceable Jumper selectable two speed operation Onboard preset to vary the…
10 factors that affect the transmission range of DIY FM Transmitters
DARK SENSITIVE SWITCH
Dark Sensitive switch project based on single BC547 transistor, Relay operates when light that falls on the LDR, goes below a set point. It’s very simple and low cost dark sensitive switch required few components. FEATURES Input : 12 VDC @ 55 mA  Relay output : NC – C – NO  Onboard preset to set…
DC MOTOR DRIVER USING L293D
This project is a DC motor driver, suitable for motors of low or medium power. Allows controlling up to 6 motors or 3 motors if you want to control the rotation of the motors. DESCRIPTION The controller is build around the IC L293D that can provide 600mA per channel, and a H-Bridge designed with transistors NPN…
TRIAC BASED LAMP DIMMER
Triac based Indecent lamp dimmer is a simple circuit and it doesn’’t requires additional power supply, works directly with 110V AC or 230V AC. DESCRIPTION It is a low cost dimmer circuit for adjusting the light brightness of incandescent, Halogen Lamp, Light Bulb load up to 250 W. FEATURES: – Input supply: 230 VAC or…