2 Channel Mini easy to use Relay shield for Arduino Nano consists of ULN2003 IC and 2 Mini 12V Relays with NO/NC contacts of 2A-24V Load Capacity. ULN2003 used as Relay coil driver. Relay can be controlled from D3 and D4 of Arduino Nano. Three-pin Header Connector CN1 and CN2 provided to connect the Load. Relay has normally open…
Arduino Nano Bar-Graph display with universal op-amp shield consists of 10 LEDs and single low voltage general purpose LMV321 op amp including few capacitors and resistors connected to op-amp pins. The op-amp proto area can be configured without any modifications to the board and all that is necessary is to select the correct resistors and…
The circuit presented here is a LED dimmer with a soft-start function. The board can drive a LED up to 12W and the circuit can manage a load up to 1A continuous with 12Vsupply. The circuit is built using SG3525 PWM IC and the IRFR120 MOSFET, SG3525 generates the PWM, and IRFR120 MOSFET drives the 12W max load. BC847…
This is another Arduino Nano shield which can drive a Brushed DC Motor in both directions with PWM signal for speed control and it also includes current trip feature. Project is based on DRV8870 IC which can handle current up to 3.6Amps, The shield also includes an IR sensor and trimmer potentiometer. Trimmer Pot helps to develop speed motor control application,…
This small constant current LED driver Nano shield has been designed using CAT4104 IC from ON semiconductor. Its 4 channel LED driver. The board has provision to mount 20 SMD 1206 LEDs. The LED can be RED, GREEN, BLUE and WHITE. Reduce the number of LED to 12 if White LEDs are used, as white…
I have written several posts similar to this one before. This experiment is again about a dark sensor based on LDR or photoresistor. There are a few components and basic soldering experience should be enough to build this up. It is a good and easy kit for electronics beginners.
About FTDI FT232RL breakout board:Â This tutorial is about making Arduino on breadboard using a basic FTDI FT232RL based breakout board.The pinout of this breakout board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is…
This is yet another dark sensor DIY kit. It is slightly different from other dark sensor kits. It has a buzzer and a photodiode that makes it different from other kits. Along with the LED, the kit turns on the buzzer whenever it senses darkness. See all the images below to get the idea for…
RGB Multicolor Lamp Sensor graph and LED controller: Temperature sensor and LED controller CD4094 control using Android Emulator HOW TO MAKE THIS SHIELD GET ALL THE PROJECTS FOR THIS SHIELD
It’s a simple project to build a stereo preamplifier using electret microphones and the cheap operational amplifier LM358. In the past, we have made few projects comprising LM358, you can check them here. This project uses the dual-channel operational amplifier LM358. Each channel is used to increase the signal of one electret microphone and it…
In this article, we have described how you can assemble your relay module for the popular clap-switch. If you have come to this page from a search engine, we recommend you to visit the following pages: Related articles: 1. About Relay module for the popular clap_switch (Get description of this kit) 2. How to connect…
As stated on the title, in this tutorial, we will rotate a motor in both directions. To achieve this, we can use a switch or the serial monitor. We will need an integrated circuit chip (IC), called H-Bridge, we will use a L293NE or SN754410 chip for our experiment.
This is a 2x100W audio amplifier board with Audio B plus Bluetooth module. It has integrated ST high-performance TDA7498 chip which supports dual channel audio amplification. Both of the channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC 12V-39V* power supply.
Two digits – Digital object counter DIY kit is one of the most popular kits designed by BuildCircuit. The kit is very popular among electronics beginners and intermediate circuit players.
Officially supported by Arduino IDE, it can burn Arduino bootloader onto chips, and practically program any Atmel AVR microcontroller by this powerful AVR ISP programmer. Summary Assembled and ready to use 6-pin AVR-standard interfaces 2 LEDs to indicate “USB/Power good” and “Busy” USB powered USB cable (A to B type) is NOT included How to use USBtinyISP…
This is a 2x8W audio amplifier board with a new AudioB plus Bluetooth module that supports Apt-X. It has perfect class-D architecture (based on TPA3110D2) and every channel has 8W power output. This board can be powered by any DC 8V-16V power supply, it can be used to drive any 4Ω or 8Ω passive speakers.
TSA1200 has a dedicated remote control, but if the remote control is broken or you want to use your own remote control, this tutorial will teach you how to pair. Note:Â The remote control used must meet the carrier frequency of 38KHz and support the NEC standard. Hardware and Software required: audio amplifier board connection cable…
The DRV101 is a low-side power switch employing a pulse-width modulated (PWM) output. Its rugged design is optimized for driving electromechanical devices such as valves, solenoids, relays, actuators, and positioners. The DRV101 module is also ideal for driving thermal devices such as heaters and lamps. PWM operation conserves power and reduces heat rise, resulting in…
