A voltage divider network is a fundamental electronic circuit used to divide a voltage into smaller fractions. It consists of two or more resistors connected in series or in a string, which create intermediate voltage points between the supply voltage and ground. Voltage dividers are commonly used for various purposes in electronics, including setting reference…
This Bluetooth music receiver connects to the Line-In or Aux input on your home audio system. You can then stream audio from your Bluetooth enabled cell phone or mp3 player to your home audio system. It comes with a new AudioB plus Bluetooth module that supports Apt-X. Note：TSA6013 can auto-detect the Aux in/Line in Audio input. Bluetooth…
The board has been design around INA217 low distortion, low noise instrumentation amplifier. The INA217 is ideal for low-level audio signals such as balanced low-impedance microphones. Many industrial, instrumentation, and medical applications also benefit from its low noise and wide bandwidth. Unique distortion cancellation circuitry reduces distortion to extremely low levels, even in high gain….
“Use your brainwaves to help you rest, guided by soothing music and fading lights.” – The NeuroDreamer Sleep Mask by Cornfield Electronics is a meditation device that flashes colored lights at your eyelids and plays brainwave beats for your ears to help you fall asleep, have lucid dreams, or for meditation. NeuroDreamer is open source…
This is yet another dark sensor DIY kit. It is slightly different from other dark sensor kits. It has a buzzer and a photodiode that makes it different from other kits. Along with the LED, the kit turns on the buzzer whenever it senses darkness. See all the images below to get the idea for…
This is a simple blinker/flasher DIY kit with 3 LEDs, 3 transistors, 3 capacitors, and few resistors. This is a very basic and easy electronic kit for beginners. It takes about 15 minutes to build the kit. It works with a 3V-5V power supply. The video shows all the assembly steps. See all the assembly…
The module described here is an isolated CAN Transceiver module. This module can be used as a standalone module or as an Arduino Uno shield. A controller area network is a two-wire high-speed serial network typically used to provide data communication between host and nodes. The high-speed controller area network transceivers offer integrated isolation, high…
In this tutorial, we will learn to make a countdown seven segment display project that counts in a sequence from number 9 to 0. To start counting, you need to press the tactile switch. At the end of counting, it flashes the LED and rings the buzzer for a few seconds.
This is yet another post related to LM317. The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and…
I recommend you to read and understand the basic theory of crystal radio published on this article:Â http://www.buildcircuit.com/how-to-make-a-batteryless-crystal-set-radio/ Making a batteryless/powerless radio is a great fun, but there are also some difficulties.
The project shown here is a microphone preamplifier that provides high quality amplification, optimized for use in computers, media and mobile applications. The pre-amplifier provides a differential input stage, making the device particularly effective when layout constraints force the microphone amplifier to be physically remote from the ECM microphone. This project features adjustable gain using…
Officially supported by Arduino IDE, it can burn Arduino bootloader onto chips, and practically program any Atmel AVR microcontroller by this powerful AVR ISP programmer. Summary Assembled and ready to use 6-pin AVR-standard interfaces 2 LEDs to indicate “USB/Power good” and “Busy” USB powered USB cable (A to B type) is NOT included How to use USBtinyISP…
This is a simple FFT 8×8 Audio LED Spectrum DIY kit. The kit package comes with all the components required to build the kit. After assembly, it works well. The assembly images very amateur and ugly soldering of the components. I should have used a reflow oven and I realized that I need to practice…
Description: This tutorial is about mp3 mode of WTV020SD-16P module. With this simple circuit, you can play AD4 format music files. At the end of the article, you can see a video output of this simple and easy project.
Description: A multivibrator has identical components(capacitors, transistors and resistors) arranged on the left and right hand sides that can be used to implement a variety of simple two-state systems such as oscillators, timers and flip-flops. In a multivibrator circuit, increasing the value of the two electrolytic capacitors increases the time each LED remains on/off.Â
This project is an one Channel Relay Driver suitable for a variety of projects. DESCRIPTION Single Channel Relay project  is a simple and convenient way to interface a relay for switching application in your project. SPECIFICATIONS: Input – 12 VDC @ 42 mA Output – SPDT relay Relay specification – 5 A @ 230 VAC…
3AMP DC Motor speed and direction controller using MC33035 IC from on semiconductor, though the MC33035 was designed to control brushless DC motor , it may also be used to control DC brush type motors. MC33035 driving a Mosfets based H-Bridge affording minimal parts count to operate a brush type motor. On board potentiometer provided…
The KA2284 is a monolithic integrated circuit designed for 5-dot LED level meter drivers with a built-in rectifying amplifier. It is suitable for AC/DC level meters such as VU meters or signal meters.
In this tutorial, we will learn how to use a servo motor. A Servo is a motor capable of making maximum rotations of 270° and is widely used in robotics and modeling. It requires a library (<Servo.h>) that is already installed on the Arduino IDE software. In this tutorial, we will vary the position of…
