See page 1 Remaining part of assembly of line following robot… Fix the nut bolt set on the PCB Solder the photo resistor/LDR as shown on the image.Make sure that the LDR is at least 5mm above the ground or spot where you are placing the robot. Solder the transparent 5mm LEDs. The LEDs should…
There are hundreds of electronics projects published on buildcircuit.com. This time we have selected few projects that should be easier for beginners to start with. Complex and difficult projects just frustrate the beginners. The best thing about the listed projects is that all come with good assembly images and most of the projects can be…
The 8 Channel Driver Arduino UNO Shield is designed to enable users to switch inductive loads for up to 800mA each channel and up to 24V DC with no heat-sink needed. It is ideal for such applications as driving 2x unipolar stepper motors, solenoids, relays, and small DC motors. It uses 2x DRV8803 Chip from Texas instruments which is 4 channel low side driver with over current protection. IC’s…
2 Channel Relay Shield for Arduino UNO is a simple and convenient way to interface 2 relays for switching applications in your project. The board has been designed using large current relay that can handle a load up to 30Amps. Relay circuit is optically isolated to prevent any kind of EMI noise. The board directly…
Optically isolator Arduino Shield has been designed to provide optically isolated I2C communication between Arduino and any other device or sensors that works with I2C protocols. I have used the ISO1540 Low-Power Bidirectional I2C Isolator IC from Texas Instruments to build this project, and the device is compatible with I2C interfaces.
BuildCircuit has previously published a project on HCSR04 ultrasonic range finder module. You can checkout the article from this link. Now, we have another article on HCSR04. It is as simple as the previous project. HCSR04 ultrasonic range finder module: The HC-SRO4 is an ultrasonic sensor which uses sonar to detect objects at a distance…
TSA3117Â is designed for amplifier manufacturers and DIY users. Bluetooth/LINE IN select switch and audio input port are designed as JST connectors. So, users can install this amplifier board in a box and connect an external switch and RCA/Mono plug to make their own audio amplifier.
To make an object counter we can use a simple dark detector circuit and a normal calculator. Pole and NO (Normally Open) terminals of a relay have to be connected to the two pins which are used to activate ‘=’ key of calculator.
As we block the light falling on LDR, the calculator starts counting.
For the calculator to work as a counter, we first need to press ‘1’ and ‘+’ keys.
This is a 2x50W audio amplifier board with a new AudioB plus Bluetooth module that supports Apt-X. It has perfect class-D architecture (based on TPA3116D2) and every channel has 50W power output. Both channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC 10V-24V power supply, it can be used to…
This is PAGE 2/2 of the article titled “How to make one transistor FM transmitter on a stripboard”. Go to previous page. Continued…. Now, solder C8 (0.1uF- code 104) capacitor. One terminal of the capacitor is connected to the +ve and the other to the -ve terminal of battery. After connecting C8, it is not…
This flasher circuit is bit different from other flasher circuits published on buildcircuit.com.
Description: An RC circuit is used to introduce time delay in circuits. A combination of resistor and capacitor gives a time constant. The following circuit shows a basic RC circuit. In the figure C1(100uF) works as a storage capacitor. When you press the switch, the capacitor charges quickly and provides base current to the transistor…
This article is about remote operated musical bell using UM3481. The M348X series IC is a mask-ROM-programmed multi melody generator , implemented by CMOS technology. It is designed to play the melody according to the previously programmed information and is capable of generating 16 songs with 3 instrument effects : piano, organ and mandolin. The device also includes a pre-amplifier which…
I have written several posts similar to this one before. This experiment is again about a dark sensor based on LDR or photoresistor. There are a few components and basic soldering experience should be enough to build this up. It is a good and easy kit for electronics beginners.
With this experimental setup you can send some text messages from your android phone to arduino and vice versa. Basically, whatever you can see on Arduino’s Serial Monitor can also be seen on the interface of Bluetooth Application that I will recommend on this article.
Check out similar robotics chassis at Buildcircuit store Sparkfun.com has recently released a simple, easy and useful robot platform for robotics amateurs. It is called “Magician Chassis”. You can use the chassis for different kinds of robots, for example, line sensing, obstacle detecting and smart phone controlled robots. I have recently published an easy project…
