This is yet another audio amplifier project. It is based on TDA2282 chip. The TDA2822M is a monolithic integrated circuit in 8 lead Minidip package. It is intended for use as dual audio power amplifier in portable cassette players and radios. Datasheet of TDA2282 You can see all the assembly images below. You can see…
I have written several projects related to LM386 based audio amplifier. LM386 is a versatile and a widely popular audio amplifier chip. The LM386M-1 and LM386MX-1 are power amplifiers designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an…
It is an excellent DIY amplifier kit for electronics beginners with excellent sound quality. You don’t hear any noise until your ears are close to speakers. This amplifier uses a TDA7297 two-channel amplifier chip.
AMP-1 amplifier uses TDA2822MÂ as an amplifier chip. This chip is STMicroelectronics (ST) developed dual-channel monolithic power amplifier IC, usually used in the pocket cassette player (WALKMAN), tape recorders and multimedia speaker for the audio amplifier. It has a simple circuit, produces good sound quality, it has a wide voltage range and other characteristics that…
This is yet another FM receiver DIY kit for electronics beginners and hobbyists. It uses the chip CXA1619. The kit package comes with all the components required to build the kit. The schematic and description is shown below: This is the PCB of the kit. The silkscreen labels can guide you through soldering. This is…
Description: The LM386 is an audio amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value from 20 to 200.
You can call this as an upgrade to LM386 based audio amplifier. We are also selling speakers for this module. This is a small but very powerful audio amplifier which is able to deliver 2.5 Watts into 4-8 ohm impedance speakers. It is based on Class D controller circuit that can be operated with 2.0V-5.5V DC….
This Bluetooth music receiver connects to the RCA input on your home audio system. You can then stream audio from your Bluetooth enabled cell phone or mp3 player to your home audio system.
This is a 2x8W audio amplifier board with AudioB plus Bluetooth module. It has a perfect class-D architecture (based on TPA3110D2) and every channel has 8W power output. This board can be powered by any DC 8V-16V power supply. It can be used to drive any 4Ω or 8Ω passive speakers.
TSA3118 is a 2x50W audio amplifier board with AudioB plus Bluetooth module. It has perfect class-D architecture (based on TPA3116D2) and each channel has 50W power output. Both channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC 10V-24V power supply. It can be used to drive any 4Ω or 8Ω…
This is a 2 x 50W audio amplifier board with AudioB plus Bluetooth module. It has a perfect class-D architecture (based on TPA3116D2) and every channel has 50W power output. Both channels are capable of outputting nominal power simultaneously and continuously. This board can be powered by any DC 10V-24V power supply, it can be used to drive…
This product does not have Bluetooth feature. This is a 2x50W audio amplifier that has integrated TI’s TPA3116 as the driver. It has a perfect class-D architecture and each channel has 50W power output. This board can be powered by any DC 12V-24V power supply. It can be used to drive any 4Ω or 8Ω passive…
BuildCircuit has written few articles about audio amplifier and music modules. One of the most popular examples is “Audio amplifier using LM386“. This article is about a bit advanced audio amplifier made using TDA7052A. Download datasheet of TDA7052A It is not wise to connect an 8 Ohm loudspeaker directly to Arduino microcontroller pins. When we…
This is one of the simplest ways of making an FM receiver. Just get a low cost FM receiver kit, make an audio amplifier using LM386, connect them together and your FM receiver is ready. Most of the commercial FM receiver kits receive the signals within the FM band, usually 88-108 MHz.
All of our Bluetooth audio amplifier boards and Bluetooth audio receiver boards use AudioB plus module as the core bluetooth receiver module. The default bluetooth name is “BT SPEAKER”. Maybe you want change it to a special name. We just updated the AudioB plus design and breakout the programming port. Now, you can change the…
