This is yet another post related to LM317. The LM317 device is an adjustable three-terminal positive-voltage regulator capable of supplying more than 1.5 A over an output-voltage range of 1.25 V to 37 V. It requires only two external resistors to set the output voltage. The device features a typical line regulation of 0.01% and…
The KA2284 is a monolithic integrated circuit designed for 5-dot LED level meter drivers with a built-in rectifying amplifier. It is suitable for AC/DC level meters such as VU meters or signal meters. 🛠️ Dive into our collection of DIY Kits, 🔊 Audio Amplifiers, Digital Scoreboards, FM transmitters, and more! 🎶 Explore endless possibilities at…
This is yet another audio amplifier project. It is based on TDA2282 chip. The TDA2822M is a monolithic integrated circuit in 8 lead Minidip package. It is intended for use as dual audio power amplifier in portable cassette players and radios. Datasheet of TDA2282 You can see all the assembly images below. You can see…
This is yet another sound activated LEDs circuit. I have previously published a similar project.
The description has been copied from manufacturer’s website. This is a PIC microcontroller-based frequency meter, subtraction frequency is set with crystal measurement functions and programmable, five digital display, easy and intuitive, all using in-line components, the circuit is simple and easy to make. Measurable frequency range: 1 Hz -50 MHz; Most commonly used to measure…
I have written several projects related to LM386 based audio amplifier. LM386 is a versatile and a widely popular audio amplifier chip. The LM386M-1 and LM386MX-1 are power amplifiers designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an…
This is yet another project based on LM358. The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent…
This is a basic electronic kit based on LM358. The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain…
This is yet another dark sensor DIY kit. It is slightly different from other dark sensor kits. It has a buzzer and a photodiode that makes it different from other kits. Along with the LED, the kit turns on the buzzer whenever it senses darkness. See all the images below to get the idea for…
This is a basic electronic kit for beginners. The kit is based on LM358, an operational amplifier and works as a flame sensor. The schematic of the kit: Check out the images below to get tips for assembling the kit. You can see the images on Flickr also. Other images
The description has been copied from eBay, so, really sorry for the bad English. When S1 is pressed, U1 NE555 pin no. 2 and 4 will get low level at the same time and NE555’s pin no.3 will also be at low level, 7 pin discharges and 6 pin also gets low level. If S1…
This is yet another metal detector kit for electronics beginners. After assembling the kit, if you take the kit close to a metal, the buzzer will turn on and the LED will flash. The sensitivity of the kit can be adjusted using the potentiometer. Parameters: NO. Parameters Value 1 Name Metal detector 2 Operating voltage…
This is a simple metal sensor DIY electronic kit for electronics beginners. Use 3V-5V battery and take metal to its proximity, it will activate the buzzer. The kit can detect metals up to 5cm. Kit parameters: Supply voltage: 3-5V Dimensions: 66 * 61MM Maximum detection range: 5CM The schematic of the kit is given below:You…
This is yet another dark/light sensor project that uses a photoresistor. This kit has an LM393 chip and there is a relay also. It is a light operated switch. 【Great School Science Project】: The light operated switch can be a great school project for children. It is widely used to help students learn basic mechanical…
It is an excellent DIY amplifier kit for electronics beginners with excellent sound quality. You don’t hear any noise until your ears are close to speakers. This amplifier uses a TDA7297 two-channel amplifier chip.
TDA2030A is widely used as a Hi-Fi audio amplifier in computer speakers. It has the current limiter as well as thermal shutdown functions. Specifications: Output Power: Maximum 18W Supply Voltage: DC 9V-24V (recommended DC 12V, this voltage to the heat sink requirements are very low. The maximum supply of this board is actually up to…
AMP-1 amplifier uses TDA2822M as an amplifier chip. This chip is STMicroelectronics (ST) developed dual-channel monolithic power amplifier IC, usually used in the pocket cassette player (WALKMAN), tape recorders and multimedia speaker for the audio amplifier. It has a simple circuit, produces good sound quality, it has a wide voltage range and other characteristics that…
This kit is very much similar to our previous projects. Check out the previous projects first: 1. Infrared based music transmitter and receiver kit 2. Wireless music transmitter and receiver circuit on a breadboard The kit package comes with 2 sets of DIY kits. One set is for laser-based music transmitter and the other is…
This is a very basic electronic DIY kit for electronics beginners. There are few LEDs in the circuit that can be turned on by sound. The larger the sound intensity the more the LEDs glow. There is a microphone in the circuit which is sensitive enough to pick surrounding sounds.
This is a DIY touch delay LED kit parts. When the user touches the kit, all the LEDs turn on. It is a very basic learning kit for beginners and learners.
